Boral Gutter Replacement Nationwide

Boral Gutter Replacement: The San Francisco Owner’s Guide

We stock Boral-compatible gutter replacement parts and install them across San Francisco, with most complete gutter replacements running between $1,400 and $3,800 depending on linear footage, roofline access, and whether we’re replacing downspouts too. We keep common Boral profiles and hangers on the truck, so more than half of our San Francisco calls are finished in a single visit. Homeowners usually find us after a winter storm, when a section of gutter pulls away from the fascia or a downspout joint separates and water starts dumping against the foundation.

Call (831) 228-3330

Which Boral Models This Applies To

Boral manufactures two gutter lines that show up regularly on San Francisco homes: their standard-profile aluminum seamless gutter systems and their steel-look pressed-metal profiles used on a lot of mid-century and modern builds. The compatibility gotcha is this: Boral’s pressed-metal profiles use a non-standard hanger spacing, 18 inches on center instead of the typical 24, so if an off-the-shelf hanger goes in, you’ll see sagging within a year. We match hangers, end caps, and miters to the original Boral profile, not just something close. If the original gutter was seamless aluminum and you can’t find a label, measure the inside width at the top opening; Boral’s most common San Francisco profile is 5-inch residential, but we’ve measured plenty of 6-inch on larger roofs and will tell you before ordering anything. For owners deciding between OEM Boral parts and quality aftermarket equivalents: Boral’s OEM hangers use a slightly thicker gauge than generic hardware-store versions, which matters in San Francisco where wind-driven rain tests every fastening. We’ll price both and explain the difference in writing before work starts.

Signs Your Boral Gutter Replacement Is Failing

• Water spilling over the lip during normal rain. This usually means the gutter pitch has failed, often because Boral’s 18-inch hanger spacing was never respected by a previous repair. One or two shims can buy you time, but a full section replacement is often the honest fix.
• Visible sag between hangers. In San Francisco’s wet-dry cycle, aluminum expands and contracts enough that undersized or improperly spaced hangers loosen seasonally. If we can see a belly in the run from the street, the fasteners are already pulling out of the fascia.
• Staining or moss on the fascia board directly behind the gutter. This is the classic San Francisco tell: salt air plus morning fog keeps the backside of gutters damp longer than the front. Behind the staining is usually a failed joint or a pinhole leak at the end cap.
• Downspout separated at the elbow or at the ground connection. On Boral systems, the joint between gutter outlet and downspout relies on a crimped connection that corrodes faster near the coast. In neighborhoods like the Sunset and Richmond, we see this on systems that are 8 to 10 years old.
• Gutter pulling away from the roofline at a corner. Boral miters are sealed at the factory, but the corner is still the weakest point for wind uplift. When a corner drops, the fasteners weren’t the problem; the backing behind the fascia often is. We check the wood before we quote.

Replacement Cost & What’s Included

For most San Francisco homes, we quote Boral gutter replacement at $28 to $42 per linear foot installed, with downspouts at $18 to $26 per foot when new runs are needed. A typical single-story 1,200-square-foot bungalow with 110 linear feet of gutter and two downspouts lands between $3,100 and $3,800. What drives the range here: roof height (a second-story Sunset flat with steep access runs higher), the condition of the fascia wood underneath, and whether we’re matching Boral’s pressed-metal profile or installing seamless aluminum instead. Every quote includes parts, labor, removal and haul-away of the old material, and Brian or one of our techs will photograph the clean-up before they leave. You get the number in writing before any work starts, and the job is covered by our 365-Day Done Right Promise. If a miter leaks or a hanger loosens within the year, we’re back out to make it right, no bill.

DIY or Call Us?

You can safely check a few things from the ground: look for obvious sag between hangers, run your eyes along the length for gaps at the shingles, and check whether water is overflowing during a light rain. That’s worth doing and costs you nothing. Where DIY goes wrong is on the ladder. Realigning a gutter run means working at height with your hands above your shoulders, and San Francisco rooflines on older Victorians and Edwardians often put a gutter 20-plus feet up on a slope. We’ve been called to more than one job where a homeowner’s repair held for a season, then failed at the same miter because the underlying seal was never addressed. If you want the job done once and covered in writing, call us at (831) 228-3330 and we’ll walk the roofline with you before we quote.

FAQs